Wireless Keypad Programming
A wireless keypad with larger buttons and backlighting allows family, friends, or service workers to easily access your garage without the need for a remote or physical key. Select your model to View the wireless programming instructions. If you need additional information about installing or programming your garage door opener or remote, contact us at (858) 547-3600.
This is an ideal secure access solution for kids returning from school, when working on exterior home projects, or when going out for a jog. Controls up to three CodeDodger® equipped garage door openers. It also uses auto-seek dual frequency (315/390 MHz).
Wireless Keypad Model OKP
- Controls up to 3 Overhead Door® garage door openers with CodeDodger® technology
- Allows a temporary PIN for guests to be set
- Compatible with all CodeDodger® equipped Overhead Door® garage door openers manufactured from 1995 to present
- CodeDodger® technology is a patented dual-band technology that provides increased security and helps to reduce or eliminate chances of signal interference.
- Features a flip-up cover to protect the keypad from the elements and backlit buttons to make entering the PIN quick and easy
- Looking for something other than white to compliment your home’s exterior? Additional lid covers can be purchased separately – almond, tan or gray.
Wireless Keypad Programming Instructions
Wireless Keypad (Model OKP-BX) with CodeDodger®
Program Keypad for One Garage Door (CodeDodger® 2)
Create Your Wireless Keypad PIN (Personal Identification Number)
On your wireless keypad:
- Press in order 3, 5, 7
- Press the PROGRAM key
- Enter your PIN (3 to 8 characters)
- Press the PROGRAM key again.
- Close the keypad cover and wait 30 seconds
Program the Keypad for a Single Door
On the power head:
- Press and hold the PROGRAM button until both LED lights turn BLUE
- Release button. Only the round LED will remain BLUE.
- Press and hold the PROGRAM button again then release. The Long LED will blink PURPLE
- Enter your PIN using the keys on the keypad
- Press the UP/DOWN button. LEDs will stay solid.
- Press the UP/DOWN button again. LEDs will turn off.
- Press any key to stop the opener. (It will automatically stop at the fully open or fully closed position.)
- The keypad backlight will turn off in approximately 30 seconds.
NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN and try again. Any keypad button will control the door for 30 seconds after the door starts moving. Rapid blinking of the red LED indicates an error. After a few seconds, the LED will turn off. Start over.
Proceed to the Mounting Instructions.
Mounting Instructions
The keypad must be mounted in sight of the door(s), at least 5 feet above the ground, and clear of any moving door parts. Mounting screws are located inside the battery compartment.
- Remove the battery cover and batteries.
- Drill a 1/16″ pilot hold for the tip mounting screw.
- Install a screw into the drilled hole, leaving a 1/8″ gap between the screw head and the wall.
- Hook the keypad over the screw.
- Mark and drill the pilot hole and fasten the bottom screw.
- Install batteries and cover.
Program Keypad for Multiple Garage Doors (CodeDodger® 2)
Create Your Wireless Keypad PIN (Personal Identification Number)
- Press in order 3, 5, 7
- Press the PROGRAM key
- Enter your PIN (3 to 8 characters)
- Press the PROGRAM key again.
- Close the keypad cover and wait 30 seconds.
Program the Keypad for Multiple Doors
All garage door openers will use the same PIN.
On the wireless keypad:
- Enter your PIN and press the PROGRAM button.
- Press the PROGRAM button again.
- Press the number of doors you wish to control (2 or 3)
- Press the program button again.
On your garage door opener power head:
- Select the first opener and press the PROGRAM/SET button until both LED lights turn BLUE.
- Release the button. Only the round LED will be BLUE.
- Press the UP/DOWN button again. LEDs will turn off.
- Press any key to stop the opener. (It will automatically stop at the fully open or closed position.)
- The keypad backlight will turn off in approximately 30 seconds.
NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN and try again. Any keypad button will control the door for 30 seconds after the door starts moving. Rapid blinking of the red LED indicates an error. After a few seconds, the LED will turn off. Start over.
Additional Instructions
Change Your PIN
- Enter your current PIN and press the PROGRAM button
- Enter your NEW PIN and press the PROGRAM button.
Using A Temporary PIN
A temporary PIN allows temporary access to your home by repair persons, meter readers, etc.
- Enter your current PIN and press the PROGRAM button 3 times.
- Enter your temporary PIN and press the PROGRAM button.
NOTE: Do NOT reprogram the garage door opener(s). A temporary PIN remains active only until the next time your normal PIN is entered.
Forgot Your PIN (Resetting Wireless Keypad)
- Press and hold the PROGRAM button
- While holding the PROGRAM button, press and hold the UP/DOWN button for 5 seconds.
- Release both buttons. You must now start from the beginning and reprogram your wireless keypad.
Changing Battery
- If the keypad backlight does not come on, this indicates the need to replace the batteries.
- Press in on the front of the battery cover and slide it off the keypad.
- Remove used batteries and replace them with “AAA” batteries.
- No programming is lost during the replacement of batteries.
Call us Today at (858) 264-3650
Overhead Door Company of Southern California™ – 12215 Kirkham Road Suite 200, Poway, CA 92064
Call Us Today at (858) 264-3650
Or Email us on the Form Below.
Business Hours: Monday – Friday 7 AM–4 PM
Call us Today at
(858) 264-3650
Or Send us an Email.